Owens Corning Blown In Insulation Nationwide

Owens Corning Blown In Insulation in Dallas: What to Know First

Owens Corning blown in insulation service in Dallas typically costs between $1.25 and $3.10 per square foot installed, and most attic jobs wrap up in a single day. We’re an independent Owens Corning service provider, which means we stock the brand but we’re not beholden to it. If another material on our truck fits your attic better, we’ll tell you that before we quote anything. Call (361) 607-0906 and a live person answers, day or night.

Call (361) 607-0906

This page is for Dallas homeowners who already have Owens Corning blown in insulation and want to know if it’s still doing its job, or who want it installed new. If your attic is working against you, your AC never had a chance. Garrett Sloane built this company on straight answers, written pricing, and the name of your technician before anyone knocks.

How Owens Corning Products Fail – and How We Fix Them

Owens Corning makes solid fiberglass blown in insulation. The AttiCat system with the expanding pink fiberglass is the most common line we see in Dallas attics, followed by older ProPink loose-fill. The product itself rarely fails on its own. What we fix most aren’t brand defects, they’re installation and environmental problems. Here’s what we’re actually finding in Dallas homes.

• Compression from foot traffic knocks the R-value down. Owens Corning AttiCat fiberglass is designed to be fluffy. Once a cable tech, HVAC crew, or a previous owner walks across it, the trapped air that does the insulating escapes. A 12-inch layer compressed to 6 inches loses roughly half its resistance to heat. We re-fluff or top it off and mark walking paths so it stays that way.
• Uneven coverage from a rushed DIY blow job. We see this constantly in Dallas ranch homes from the 1980s and 90s. The original installation went thin at the eaves and heavy in the center because whoever ran the machine didn’t work methodically. AttiCat is easy to apply but easy to apply badly. We measure depth across the entire attic floor, not just one spot, and level it before adding anything.
• Air leaks through the attic floor render even good Owens Corning insulation less effective. Fiberglass filters heat, not air. If the can lights, bathroom fan boxes, and top plates aren’t sealed, your conditioned air escapes into the attic regardless of how much pink fiberglass sits on top. We seal these bypasses with foam or caulk before we assess whether you need more insulation at all. Half the time, the insulation was fine and the air sealing was the missing piece.
• Moisture from Dallas humidity steams up and settles into the top layer. AttiCat fiberglass doesn’t wick water the way cellulose does, but if your bathroom fans vent into the attic or the soffit vents are blocked, moisture collects on the top surface and mats the fibers down. That matted crust cuts airflow. We fix the venting first, then pull out the damaged top layer and top it off clean.
• Rodent activity destroys whole sections in older ProPink installs. Squirrels and rats love a warm attic in January. They burrow and nest in the loose fill, compacting it and leaving droppings throughout. We remove the contaminated material, seal the entry points, and reinstall fresh Owens Corning blown in or a comparable material you’ve approved in writing.

Our Owens Corning Blown In Insulation Process

You’ll know exactly who is coming to your house before they arrive. Here’s how a typical Owens Corning job goes from your first call to our final walkthrough.

1. 1
   Call (361) 607-0906. A live person, not a voicemail, answers 24/7. We ask about your home, your current insulation, and what’s bothering you: high bills, uneven rooms, hot ceilings.
2. 2
   We send a written quote before work starts. No verbal estimates, no “we’ll see when we get there.” Garrett or one of our techs names the material, the depth target, the square footage, and the total dollar figure. You approve it in writing first.
3. 3
   Your technician is named and photo-badged before the visit. This is the Threshold Standard. We send you the name, photo, and credentials of the person coming to your door. If someone else shows up, the visit is free and we make it right.
4. 4
   We prep the attic. That means sealing bypasses, addressing any venting problems, and protecting your access point before we run the AttiCat machine or whichever Owens Corning product we’ve agreed on.
5. 5
   We blow the insulation to spec. We don’t guess at depth. We mark the target depth on the attic framing and blow until we hit it, evenly, everywhere, including the hard-to-reach eaves.
6. 6
   We test, walk you through it, and hand you the 365-Day Done Right Promise. We show you the depth, show you the coverage, and give you a written guarantee covering labor and materials for a full year. If it’s not done right, we come back free.

What Owens Corning Blown In Insulation Costs in Dallas

Here’s what we typically see in Dallas for Owens Corning blown in insulation work. These are installed prices including labor and materials.

• Attic top-off, 1,000 square feet, adding ~6 inches of AttiCat to get to R-49: $1,250 to $1,750
• New blown in insulation, 1,000 square feet, full install to R-49: $1,500 to $1,900
• Full removal of old or contaminated insulation plus new Owens Corning blown in: $2,800 to $4,200 for the same 1,000 square feet, depending on access and how much has to come out
• Air sealing before blowing: $450 to $900, depending on how many can lights, fans, and top plates need to be sealed

What moves the price is attic access, existing depth, whether removal is needed, and how many air leaks we have to close before the insulation matters. You’ll get the exact number in writing before any work starts. Call (361) 607-0906 and we’ll scope it out.

Why Dallas Homeowners Call Aspen Attic Insulation Dallas for Owens Corning Work

We’ve been doing this since 2002, starting on the West Coast and working our way across Dallas for years now, from quiet subdivisions to older homes near White Rock Lake that leak heat like a screen door. Garrett learned insulation at Los Angeles Trade-Technical College and has crawled through more Dallas attics than he can count. What’s different about us isn’t the Owens Corning product, it’s how we run the job.

Every visit works to the Threshold Standard: background-checked, identity-verified, uniformed techs who show you a photo ID at the door. You get the tech’s name and face before the visit. You get the price before the work. You get a written 365-day guarantee covering labor and materials. We carry eight insulation brands, including Reflectix for radiant barrier work, so we’re not forcing a product that doesn’t match your attic. We’re not affiliated with Owens Corning. We’re just the Dallas crew that installs it right and stands behind it in writing.

FAQs